다운로드 Gearhead Pro

다른 한편에서는 원활한 경험을하려면 파일을 장치에 다운로드 한 후 파일을 사용하는 방법을 알아야합니다. APK 파일은 Android 앱의 원시 파일이며 Android 패키지 키트를 의미합니다. 모바일 앱 배포 및 설치를 위해 Android 운영 체제에서 사용하는 패키지 파일 형식입니다.
네 가지 간단한 단계에서 사용 방법을 알려 드리겠습니다. Gearhead Pro 귀하의 전화 번호.

1 단계 : 다운로드 Gearhead Pro 귀하의 기기에서

아래의 다운로드 미러를 사용하여 지금 당장이 작업을 수행 할 수 있습니다. 그것의 99 % 보장 . 컴퓨터에서 파일을 다운로드하는 경우, 그것을 안드로이드 장치로 옮기십시오.  

2 단계 : 기기에 타사 앱 허용

설치하려면 Gearhead Pro 타사 응용 프로그램이 현재 설치 소스로 활성화되어 있는지 확인해야합니다. 메뉴 > 설정 > 보안> 으로 이동하여 알 수없는 소스 를 선택하여 휴대 전화가 Google Play 스토어 이외의 소스에서 앱을 설치하도록 허용하십시오.

3 단계 : 파일 관리자로 이동

이제 위치를 찾으십시오 Gearhead Pro 방금 다운로드 한 파일입니다.
일단 당신이 Gearhead Pro 파일을 클릭하면 일반 설치 프로세스가 시작됩니다. 메시지가 나타나면 "예" 를 누르십시오. 그러나 화면의 모든 메시지를 읽으십시오.

4 단계 : 즐기십시오

Gearhead Pro 이 (가) 귀하의 기기에 설치되었습니다. 즐겨!

개발자 설명

From a hobby gearhead to a professional engine or chassis builder, you’ll want Gearhead Pro! Gearhead Pro is the calculator app that us gearheads use for many performance automotive parameters. It calculates or estimates numerous engine, exhaust, gearing, tire, suspension, acceleration, weather effects, and other vehicle parameters along with automotive unit conversions and fastener torque and threading parameters. Gearhead Pro works in both standard and metric units and even has advanced settings to customize the calculations to your specific scenario so you can select the most compatible parts for your application. Gearhead Pro calculates or estimates: Speed/Gearing - Engine RPM from vehicle speed, gearing, tire size - Vehicle Speed from engine RPM, gearing, tire size - Axle Gear needed for a specific RPM at a certain speed with a given tire size - Tire Diameter and Cross section width from sidewall size - Simple gear ratios based on drive and driven tooth count Boat - Boat Speed from propeller pitch, slip, RPM and gearing - Boat Propeller Slip from pitch, RPM, Speed, and gearing - Simple gear ratios based on drive and driven tooth count Engine - Displacement from cylinders, bore, and stroke - Bore/Stroke ratio - Static Compression Ratio - Average Piston Speed - Airflow - Airflow w/boost pressure - Connecting Rod Ratio - Maximum connecting rod angle from cylinder axis - Compression Height (piston wrist pin height) - Dynamic Compression Ratio from the point the intake valve closes - Effective Compression Ratio (both static and dynamic) using boost pressure - Piston Position relative to crank angle from TDC - Head gasket volume (from bore and compressed thickness if round) - Valve opening and closing events from the cam duration, IC, and LSA - Cam specs from the valve opening and closing events - Valve overlap - Valve lift based on new rocker ratio or lobe lift and rocker ratio - Valve spring forces from valve spring specs to actual installed height and lift - Mark dimension on your balancer to set a desired timing advance Engine Externals - Minimum air filter size for your engine - Recommended header primary tube size for your engine - Recommended exhaust size for your engine - Cross-sectional flow area of a pipe, or the pipe size from a desired flow area - Pressure ratio and mass airflow for turbocharger selection - Power potential of a turbocharged engine configuration - Pressure ratio and airflow for supercharger selection - Power potential of a supercharged engine configuration - Starting pulley ratios and sizes for a supercharged engine Suspension - Instant center, Roll Center and Axis, and Anti-Squat of a 4 link rear suspension - Cg height of your vehicle using the raise one end method - Combined and secondary spring rates of a dual spring coil-over setup Weather - Specific humidity - Air Density Index - MSA density altitude - Power Correction Factor of the current weather conditions Power - Power from Torque and RPM, or vice versa Fasteners and Threading - Convert fastener torque units to your torque wrench unit - Lookup or calculate a cutting tap drill size either standard or custom thread - Torque of a fastener based on thread size and pitch, fastener grade, thread finish… - Minimum thread length engagement of a fastener in a tapped hole Unit Conversions - Length - Area - Volume - Absolute Pressure - Engine Vacuum/Boost - Temperature - Speed - Volume Flow - Mass Flow - Power - Torque - BSFC Fuel System - Total Fuel system flow for fuel pump selection - Fuel injector flow for injector selection - Convert an injector flow rating to a new pressure or flow Acceleration - Power of your engine based on your drag racing performance and weight - Drag performance based on power and weight - Time you would run on a ¼ mile track (.4 km) based on 1/8 mile (.2 km) performance - ET or speed based on a previous ET or speed and a weight or weather change - More power needed to achieve a new ET or speed